Selasa, 30 November 2021

Bathroom Pipe Sealant

Bathroom Pipe Sealant

PlumbingSupply.com®

PlumbingSupply.com®

Pipe Sizes Info

The outside diameter (o.d.) shown is for standard IPS, Schedule 40, pipe (PVC, stainless, brass, steel, etc.)
(not for CPVC, PEX, PB or copper pipe)

Standard Nipples and Pipe Sizing
Pipe Size Outside Diameter (O.D.) Circumference Threads Per Inch
1/8" 0.405" 1.272" 27
1/4" 0.540" 1.696" 18
3/8" 0.675" 2.121" 18
1/2" 0.840" 2.639" 14
3/4" 1.050" 3.299" 14
1" 1.315" 4.131" 11 1/2
1 1/4" 1.660" 5.215" 11 1/2
1 1/2" 1.900" 5.969" 11 1/2
2" 2.375" 7.461" 11 1/2
2 1/2" 2.875" 9.032" 8
3" 3.500" 10.995" 8
4" 4.500" 14.137" 8
5" 5.563" 17.476" 8
6" 6.625" 20.812" 8
8" 8.625" 27.095" 8
10" 10.750" 33.771" 8
12" 12.750" 40.054" 8

Circumference = distance around the outside of pipe

Pipe sizes do not refer to any physical dimensions. The outside diameter of each pipe must be measured for size identification. For example, a 3/4" NPT pipe thread has an outside diameter of 1.050 inches. Each thread size has a defined number of threads per inch (TPI). The 3/4" NPT pipe thread has 14 threads per inch. Both the TPI (threads per inch) and OD (outside diameter) of the thread are required for positive identification of thread size because several sizes have the same TPI.


All pipe thread types used in plumbing are specified by the American National Standard for pipe as accredited by the American National Standards Institute (ANSI).

National Pipe Threads (NPT) have tapered threads. These are the most common threads used for general purposes. NPT threads are used for joining and sealing pipe to fittings in low pressure air or liquids and also mechanical applications. The tapered thread is 3/4" over one foot of length. Tapered threads are deeper at the end of the pipe and are increasingly shallower the further they are from the end of the pipe. The taper on the pipe only allows the pipe to screw inside the fitting until it is forced to stop because of the taper. The distance the pipe can be screwed into the fitting is specified by the ANSI standard. After tightening with a wrench the threads may have slight spaces between the pipe and fitting which could cause a leak so a pipe sealant must be used to ensure any gaps are filled.

The Dry-seal thread (NPTF) also have tapered threads. NPTF threads are used when the application is such that pipe sealing compounds may fail due to higher heat or pressure than normal NPT threads can withstand. The threads are designed to seal mechanically by slightly, but sufficiently, crushing the threads when tightened with a wrench. This allows for joining the pipe and fitting without sealants.

The NPT and NPTF threads are interchangeable with sealants such as PTFE tape. None of the other thread standards are interchangeable. Female NPT threads can be designated as "FPT" and male NPT threads can be designated as "MPT."

National Standard Free-Fitting Straight Mechanical Pipe Threads (NPSM) have straight threads which are only used for joining. A washer or gasket is needed to seal this type of threaded connection.

Three less common threads exist, the Garden Hose Thread (GHT), Fire Hose Coupling (NST) and British Standard Taper Pipe Thread (BSPT).

Definitions of Pipe Thread Acronyms
NPT National Pipe Thread (tapered)
FPT Female Pipe Thread (NPT)
MPT Male Pipe Thread (NPT)
IPS Iron pipe size (NPT)
PTF SAE short taper pipe thread - dryseal
NPTF American National taper pipe thread for dryseal pressure-tight joints
NPSM American National straight pipe thread for mechanical joints
NPSI American National straight intermediate pipe thread
GHT Garden Hose Thread
NST Fire Hose Thread
BSPT British Standard taper pipe thread (metric dimensions)

Customer Testimonials

"You made figuring size of pipes easy... good work."
- Ann Marr, Grosse Pointe Park, Michigan 48230-1748

"Your website was extremely informative and helpful, especially for such a small order from single person. You are a definite KEEPER!! I was, and still am, very pleased with your assistance solving a 50 year old problem for me."
- David Werlein, Brewster, Washington 98812-9613

Please note that every customer testimonial shown on our pages has given us written permission to quote them. Our customer's privacy is very important to us, and we will never give, share or sell contact information or e-mail addresses to anyone!

return to top ↑

Copyright© 1995-2020 PlumbingSupply.com.
All Rights Reserved.

Copyright© 1995-2020 PlumbingSupply.com. All Rights Reserved.

Bathroom Pipe Sealant

Source: https://www.plumbingsupply.com/info-pipesizes.html

Show comments
Hide comments
Tidak ada komentar:
Tulis komentar

Must Read

Back to Top
banner